125mm (5") Round To Round Pipe Connector Collar
- Fire resistant - Mould resistant - Recyclable
- In stock
- Backordered, shipping soon
Optional extras — you can buy the product on its own.
Add the components you need from the ducting range.
Browse components +
Match the dimensions and connection type. Round and flat ducting may require an adaptor.
View details125mm Round to 150mm × 70mm Flat Ducting — Vertical 90° Bend
This connector joins a 125mm round ducting pipe (or 125mm flexible aluminium tube) to a 150mm × 70mm flat rectangular ducting pipe at a right angle, routing the duct through a vertical 90° corner. It is part of the Luxair 5" push-fit airtight ducting system.
Where This Component Is Used
Use this bend where your cooker hood ducting needs to change direction at a vertical right angle — for example where the duct run leaves the hood body and turns to run horizontally along a wall or into a ceiling void, or where a run needs to transition between round and flat ducting formats at a corner.
The 5" Push-Fit System
This component is part of the Luxair 125mm (5") push-fit airtight ducting range. The system combines 150mm × 70mm flat rectangular ducting and 125mm round ducting — both formats carry equivalent airflow rates and are fully interchangeable within the system. All components connect by push-fit for an airtight seal without adhesive or clips. The full range includes straight sections, bends, adapters, elbows, and wall outlets to complete any standard cooker hood ducting installation.
Ducting Size Guide
Selecting the correct ducting diameter for your motor output ensures maximum extraction performance:
- Below 450m³/hr → 100mm (4") ducting
- 450–750m³/hr → 125mm (5") or 150mm (6") ducting
- 750–2,000m³/hr → 150mm (6") or 200mm (8") ducting
✓ 125mm round to 150mm × 70mm flat — vertical 90° bend — check product title to confirm exact component before ordering
✓ Connects 125mm round ducting or 125mm flexible aluminium tube to 150mm × 70mm flat rectangular ducting
✓ 90° vertical bend — routes ducting through a right-angle corner smoothly for consistent airflow
✓ Part of the Luxair 5" (125mm) push-fit airtight ducting system — no adhesive or clips required; push-fit connection throughout
✓ Compatible with both 150mm × 70mm flat and 125mm round components — both carry equivalent airflow rates within the system
✓ Suitable for standard cooker hood ducting installations — wall, ceiling, and cavity duct runs
✓ Fast UK despatch — express overnight service available
View details150mm × 70mm Flat Ducting — Vertical 90° Elbow Bend
This elbow connects two 150mm × 70mm flat rectangular ducting sections at a vertical right angle, routing the duct run smoothly through a 90° corner without restricting airflow. It is part of the Luxair 5" push-fit airtight ducting system.
Where This Component Is Used
Use this elbow where a flat rectangular duct run needs to change direction at a vertical right angle — typically at ceiling level, within a kitchen cabinet void, or where the duct transitions from a vertical to a horizontal run. The low-profile 150mm × 70mm dimensions allow the duct to be concealed easily in restricted spaces such as between wall units and ceiling soffits.
The 5" Push-Fit System
This component is part of the Luxair 125mm (5") push-fit airtight ducting range. The system combines 150mm × 70mm flat rectangular ducting and 125mm round ducting — both formats carry equivalent airflow rates and are fully interchangeable within the system. All components connect by push-fit for a patent-protected airtight seal with no ducting tape, adhesive, or clips required. Suitable for kitchen, bathroom, and utility room extract systems, as well as whole-house ventilation installations. The full range includes straight sections, bends, elbows, adapters, and wall outlets to complete any standard ducting installation.
Ducting Size Guide
Selecting the correct ducting diameter for your motor output ensures maximum extraction performance:
- Below 450m³/hr → 100mm (4") ducting
- 450–750m³/hr → 125mm (5") or 150mm (6") ducting
- 750–2,000m³/hr → 150mm (6") or 200mm (8") ducting
✓ 150mm × 70mm flat ducting vertical 90° elbow — connects two flat rectangular duct sections at a right angle corner
✓ Smooth 90° bend — maintains consistent airflow through corners without restriction
✓ Low-profile 150mm × 70mm dimensions — conceals easily in restricted spaces including cabinet voids and ceiling soffits
✓ Patent-protected push-fit airtight seal — no ducting tape, adhesive or clips required
✓ Part of the Luxair 5" (125mm) push-fit airtight ducting system — fully compatible with all other components in the range
✓ Suitable for kitchen, bathroom, utility room and whole-house extract systems
✓ Fast UK despatch — express overnight service available
View details150mm × 70mm Flat Ducting — Horizontal 90° Elbow Bend
This elbow connects two 150mm × 70mm flat rectangular ducting sections at a horizontal right angle, routing the duct run smoothly through a 90° corner in the horizontal plane without restricting airflow. It is part of the Luxair 5" push-fit airtight ducting system.
Where This Component Is Used
Use this elbow where a flat rectangular duct run needs to change direction horizontally — typically where the duct turns a corner along a wall at the same height, such as running along the top of kitchen wall units and turning a room corner. The low-profile 150mm × 70mm dimensions allow the duct to be concealed easily in restricted spaces such as between wall units and ceiling soffits.
The 5" Push-Fit System
This component is part of the Luxair 125mm (5") push-fit airtight ducting range. The system combines 150mm × 70mm flat rectangular ducting and 125mm round ducting — both formats carry equivalent airflow rates and are fully interchangeable within the system. All components connect by push-fit for a patent-protected airtight seal with no ducting tape, adhesive, or clips required. Suitable for kitchen, bathroom, and utility room extract systems, as well as whole-house ventilation installations. The full range includes straight sections, bends, elbows, adapters, and wall outlets to complete any standard ducting installation.
Ducting Size Guide
Selecting the correct ducting diameter for your motor output ensures maximum extraction performance:
- Below 450m³/hr → 100mm (4") ducting
- 450–750m³/hr → 125mm (5") or 150mm (6") ducting
- 750–2,000m³/hr → 150mm (6") or 200mm (8") ducting
✓ 150mm × 70mm flat ducting horizontal 90° elbow — connects two flat rectangular duct sections at a horizontal right angle corner
✓ Smooth 90° horizontal bend — maintains consistent airflow through corners without restriction
✓ Low-profile 150mm × 70mm dimensions — conceals easily along wall unit runs and in restricted ceiling spaces
✓ Patent-protected push-fit airtight seal — no ducting tape, adhesive or clips required
✓ Part of the Luxair 5" (125mm) push-fit airtight ducting system — fully compatible with all other components in the range
✓ Suitable for kitchen, bathroom, utility room and whole-house extract systems
✓ Fast UK despatch — express overnight service available
View details150mm × 70mm Flat Ducting Pipe — 1 Metre
This is the standard 1 metre straight section of 150mm × 70mm flat rectangular ducting pipe, suitable for cooker hood installations with motor speeds up to 750m³/hr. It is part of the Luxair 5" push-fit airtight ducting system.
Why Flat Rigid Ducting Outperforms Flexible Aluminium Pipe
Rigid flat ducting is significantly more efficient than flexible aluminium pipe. Flexible aluminium tube has a corrugated interior surface that creates turbulence and resistance in the airflow, reducing extraction performance — particularly over longer duct runs. The smooth interior walls of rigid flat ducting allow air to travel freely with minimal resistance, delivering consistently higher extraction rates from the same motor. Luxair recommends rigid flat ducting for all ceiling extractor hoods and all extractors with a minimum motor speed of 350m³/hr.
The 5" Push-Fit System
This pipe is part of the Luxair 125mm (5") push-fit airtight ducting range. The system combines 150mm × 70mm flat rectangular ducting and 125mm round ducting — both formats carry equivalent airflow rates and are fully interchangeable within the system. All components connect by push-fit for a patent-protected airtight seal with no ducting tape, adhesive, or clips required. Suitable for kitchen, bathroom, and utility room extract systems, as well as whole-house ventilation installations. The full range includes bends, elbows, adapters, and wall outlets to complete any standard ducting installation.
Ducting Size Guide
Selecting the correct ducting diameter for your motor output ensures maximum extraction performance:
- Below 450m³/hr → 100mm (4") ducting
- 450–750m³/hr → 125mm (5") or 150mm (6") ducting
- 750–2,000m³/hr → 150mm (6") or 200mm (8") ducting
✓ 150mm × 70mm flat rigid ducting pipe — 1 metre length
✓ Suitable for cooker hoods up to 750m³/hr — recommended for all ceiling extractors and motors of 350m³/hr and above
✓ More efficient than flexible aluminium pipe — smooth interior walls reduce airflow resistance; corrugated flex tube creates turbulence and reduces extraction performance
✓ Patent-protected push-fit airtight seal — no ducting tape, adhesive or clips required at joints
✓ Part of the Luxair 5" (125mm) push-fit airtight ducting system — fully compatible with all bends, elbows, adapters and outlets in the range
✓ Suitable for kitchen, bathroom, utility room and whole-house extract systems
✓ Fast UK despatch — express overnight service available
View details150mm × 70mm Flexible Ducting Hose — Extends to 500mm
This flexible hose connects two 150mm × 70mm flat rectangular ducting sections and extends up to 500mm, bending at virtually any angle to route the duct run around obstacles or through tight spaces. It is part of the Luxair 5" push-fit airtight ducting system.
Where This Component Is Used
Unlike rigid bends which are fixed at 90°, this flexible hose adapts to any angle — making it the correct solution wherever a precise bend angle isn't known in advance or where rigid components can't be fitted. It is particularly suited to ceiling cooker hood installations where the duct must navigate between ceiling joists, up and over structural obstacles, or through irregular ceiling voids where a fixed-angle elbow would be impractical.
When to Use Flexible Hose vs Rigid Bends
Rigid 90° elbows and bends should be used wherever the installation allows — they offer lower airflow resistance than flexible hose. Use this flexible hose where the installation requires it: tight joist spaces, irregular angles, or where rigid components physically cannot be fitted. Keep the flexible section as short and straight as possible to minimise resistance in the duct run.
The 5" Push-Fit System
This component is part of the Luxair 125mm (5") push-fit airtight ducting range. The system combines 150mm × 70mm flat rectangular ducting and 125mm round ducting — both formats carry equivalent airflow rates and are fully interchangeable within the system. All components connect by push-fit for a patent-protected airtight seal with no ducting tape, adhesive, or clips required. Suitable for kitchen, bathroom, and utility room extract systems, as well as whole-house ventilation installations.
Ducting Size Guide
Selecting the correct ducting diameter for your motor output ensures maximum extraction performance:
- Below 450m³/hr → 100mm (4") ducting
- 450–750m³/hr → 125mm (5") or 150mm (6") ducting
- 750–2,000m³/hr → 150mm (6") or 200mm (8") ducting
✓ 150mm × 70mm flexible ducting hose — extends up to 500mm; bends at virtually any angle
✓ Connects two 150mm × 70mm flat ducting sections — at any required angle without a fixed-degree elbow
✓ Ideal for ceiling hood installations — navigates between joists, around structural obstacles, and through irregular ceiling voids
✓ Use where rigid components cannot fit — flexible section should be kept as short and straight as possible to minimise airflow resistance
✓ Patent-protected push-fit airtight seal — no ducting tape, adhesive or clips required
✓ Part of the Luxair 5" (125mm) push-fit airtight ducting system — fully compatible with all rigid components in the range
✓ Suitable for kitchen, bathroom, utility room and whole-house extract systems
✓ Fast UK despatch — express overnight service available
View details150mm × 70mm Flat Ducting Pipe Clips
These pipe clips are designed to secure 150mm × 70mm flat rectangular ducting to walls, ceilings, joists, and structural surfaces throughout a duct run. Each pack includes screws — please check that the fixings supplied are suitable for the surface type you are fixing to before installation.
Where These Clips Are Used
Suitable for use wherever the duct run needs to be fixed in place — including restricted spaces such as under floorboards, above ceilings, behind cavity walls, and within joist voids. Compliant with Part F of the Building Regulations for both domestic and commercial installations.
Ducting Size Guide
Selecting the correct ducting diameter for your motor output ensures maximum extraction performance:
- Below 450m³/hr → 100mm (4") ducting
- 450–750m³/hr → 125mm (5") or 150mm (6") ducting
- 750–2,000m³/hr → 150mm (6") or 200mm (8") ducting
The 5" Push-Fit System
These clips are compatible with the Luxair 125mm (5") push-fit airtight ducting range. The system combines 150mm × 70mm flat rectangular ducting and 125mm round ducting — both formats carry equivalent airflow rates and are fully interchangeable within the system. The full range includes straight pipe sections, bends, elbows, adapters, and wall outlets to complete any standard ducting installation.
✓ Pipe clips for 150mm × 70mm flat rectangular ducting — secures duct runs to walls, ceilings, joists and structural surfaces
✓ Screws included — check fixings are suitable for your surface type before installation
✓ Suitable for restricted spaces — under floorboards, above ceilings, behind cavity walls and within joist voids
✓ Part F Building Regulations compliant — suitable for domestic and commercial installations
✓ Compatible with the Luxair 5" (125mm) push-fit airtight ducting system
✓ Fast UK despatch — express overnight service available
View details150mm × 70mm Flat Ducting Straight Connector
This connector joins two 150mm × 70mm flat rectangular ducting sections together on a straight duct run, extending the run beyond a single pipe length. It is part of the Luxair 5" push-fit airtight ducting system.
Important — Use Pipe Clips Either Side of Each Joint
On longer duct runs of one metre or more, pipe clips must be fitted either side of each connector joint to prevent the ducting from sagging under its own weight. Sagging joints can break the airtight seal and reduce extraction performance. See the 150mm × 70mm flat ducting pipe clips in the Luxair ducting range.
Ducting Size Guide
Selecting the correct ducting diameter for your motor output ensures maximum extraction performance:
- Below 450m³/hr → 100mm (4") ducting
- 450–750m³/hr → 125mm (5") or 150mm (6") ducting
- 750–2,000m³/hr → 150mm (6") or 200mm (8") ducting
The 5" Push-Fit System
This component is part of the Luxair 125mm (5") push-fit airtight ducting range. The system combines 150mm × 70mm flat rectangular ducting and 125mm round ducting — both formats carry equivalent airflow rates and are fully interchangeable within the system. All components connect by push-fit for a patent-protected airtight seal with no ducting tape, adhesive, or clips required at joints. The full range includes straight pipe sections, bends, elbows, adapters, and wall outlets to complete any standard ducting installation.
✓ 150mm × 70mm flat ducting straight connector — joins two flat rectangular duct sections on a continuous straight run
✓ Patent-protected push-fit airtight seal — no ducting tape, adhesive or clips required at the joint itself
✓ Use pipe clips either side of each joint on runs of 1 metre or more — prevents sagging and maintains airtight seal throughout
✓ Part of the Luxair 5" (125mm) push-fit airtight ducting system — fully compatible with all bends, elbows, adapters and outlets in the range
✓ Suitable for kitchen, bathroom, utility room and whole-house extract systems
✓ Fast UK despatch — express overnight service available
View details125mm Round Ducting Pipe — 1 Metre
This is the standard 1 metre straight section of 125mm round rigid ducting pipe, suitable for cooker hood installations with motor speeds up to 750m³/hr. It is part of the Luxair 5" push-fit airtight ducting system.
Why Rigid Round Ducting Outperforms Flexible Aluminium Pipe
Rigid round ducting is significantly more efficient than flexible aluminium pipe. Flexible aluminium tube has a corrugated interior surface that creates turbulence and resistance in the airflow, reducing extraction performance — particularly over longer duct runs. The smooth interior walls of rigid round ducting allow air to travel freely with minimal resistance, delivering consistently higher extraction rates from the same motor. For any installation where rigid ducting can be fitted, it is always the preferred choice over flexible aluminium pipe.
Ducting Size Guide
Selecting the correct ducting diameter for your motor output ensures maximum extraction performance:
- Below 450m³/hr → 100mm (4") ducting
- 450–750m³/hr → 125mm (5") or 150mm (6") ducting
- 750–2,000m³/hr → 150mm (6") or 200mm (8") ducting
The 5" Push-Fit System
This pipe is part of the Luxair 125mm (5") push-fit airtight ducting range. The system combines 125mm round ducting and 150mm × 70mm flat rectangular ducting — both formats carry equivalent airflow rates and are fully interchangeable within the system. All components connect by push-fit for a patent-protected airtight seal with no ducting tape, adhesive, or clips required. Suitable for kitchen, bathroom, and utility room extract systems, as well as whole-house ventilation installations. The full range includes bends, elbows, adapters, and wall outlets to complete any standard ducting installation.
✓ 125mm round rigid ducting pipe — 1 metre length
✓ Suitable for cooker hoods up to 750m³/hr — rigid round ducting recommended for all powerful extractor installations
✓ More efficient than flexible aluminium pipe — smooth interior walls reduce airflow resistance; corrugated flex tube creates turbulence and reduces extraction performance
✓ Patent-protected push-fit airtight seal — no ducting tape, adhesive or clips required at joints
✓ Part of the Luxair 5" (125mm) push-fit airtight ducting system — fully compatible with all 150×70mm flat components via adapters
✓ Suitable for kitchen, bathroom, utility room and whole-house extract systems
✓ Fast UK despatch — express overnight service available
View details125mm Round to 150mm × 70mm Flat Ducting Connector
This adapter connects a 125mm round ducting pipe (or 125mm flexible aluminium tube) to a 150mm × 70mm flat rectangular ducting pipe on a straight run. Unlike the 90° bend version, this connector makes the transition between round and flat formats in a straight line and can be used in either a vertical or horizontal position. It is part of the Luxair 5" push-fit airtight ducting system.
Where This Component Is Used
Use this connector wherever your duct run needs to transition between round and flat ducting formats without changing direction — for example, where the round outlet of a cooker hood or ceiling extractor connects to a flat rectangular duct run along a wall or ceiling, or where a flat section terminates into a round pipe to connect to a fan or wall outlet. The connector works equally in vertical and horizontal orientations.
Ducting Size Guide
Selecting the correct ducting diameter for your motor output ensures maximum extraction performance:
- Below 450m³/hr → 100mm (4") ducting
- 450–750m³/hr → 125mm (5") or 150mm (6") ducting
- 750–2,000m³/hr → 150mm (6") or 200mm (8") ducting
The 5" Push-Fit System
This component is part of the Luxair 125mm (5") push-fit airtight ducting range. The system combines 125mm round ducting and 150mm × 70mm flat rectangular ducting — both formats carry equivalent airflow rates and are fully interchangeable within the system. All components connect by push-fit for a patent-protected airtight seal with no ducting tape, adhesive, or clips required. The full range includes straight pipe sections, bends, elbows, and wall outlets to complete any standard ducting installation.
✓ 125mm round to 150mm × 70mm flat ducting straight connector — transitions between round and flat duct formats without changing direction
✓ Use in vertical or horizontal position — works in either orientation within the duct run
✓ Connects 125mm round rigid pipe or 125mm flexible aluminium tube to 150mm × 70mm flat rectangular ducting
✓ Patent-protected push-fit airtight seal — no ducting tape, adhesive or clips required
✓ Part of the Luxair 5" (125mm) push-fit airtight ducting system — both round and flat formats carry equivalent airflow rates
✓ Suitable for kitchen, bathroom, utility room and whole-house extract systems
✓ Fast UK despatch — express overnight service available
View details125mm Round Ducting — 90° Elbow Bend
This elbow connects two 125mm round rigid ducting sections at a right angle, routing the duct run smoothly through a 90° corner without restricting airflow. It is part of the Luxair 5" push-fit airtight ducting system.
Where This Component Is Used
This elbow is particularly suited to two common installation scenarios. For wall-mounted cooker hoods ducted directly through an outside wall, the elbow connects the round outlet of the hood to the duct section passing through the wall — turning the run from vertical to horizontal in a single component. For island cooker hood installations, the elbow routes the duct from the hood body up into the ceiling void, turning the run at the ceiling level to continue horizontally above. It can also be used in any installation where a 90° direction change is required in a round duct run.
Ducting Size Guide
Selecting the correct ducting diameter for your motor output ensures maximum extraction performance:
- Below 450m³/hr → 100mm (4") ducting
- 450–750m³/hr → 125mm (5") or 150mm (6") ducting
- 750–2,000m³/hr → 150mm (6") or 200mm (8") ducting
The 5" Push-Fit System
This component is part of the Luxair 125mm (5") push-fit airtight ducting range. The system combines 125mm round ducting and 150mm × 70mm flat rectangular ducting — both formats carry equivalent airflow rates and are fully interchangeable within the system. All components connect by push-fit for a patent-protected airtight seal with no ducting tape, adhesive, or clips required. The full range includes straight pipe sections, connectors, adapters, and wall outlets to complete any standard ducting installation.
✓ 125mm round ducting 90° elbow — connects two round rigid duct sections at a right angle corner
✓ Smooth 90° bend — maintains consistent airflow through corners without restriction
✓ Ideal for wall-mounted hood installations — connects hood outlet to through-wall duct section in a single component
✓ Ideal for island hood installations — routes duct from hood body into ceiling void at 90°
✓ Patent-protected push-fit airtight seal — no ducting tape, adhesive or clips required
✓ Part of the Luxair 5" (125mm) push-fit airtight ducting system — fully compatible with all flat and round components in the range
✓ Suitable for kitchen, bathroom, utility room and whole-house extract systems
✓ Fast UK despatch — express overnight service available
View detailsAluminium Ducting Joint Tape — 50mm × 45m Roll
This is a silver-faced aluminium foil sealing tape for securing and sealing ducting joints, adapters, and ventilation connections. Supplied on a white paper liner, the tape is self-adhesive and applies directly to ducting surfaces to prevent air escaping at joints — maintaining full extraction power throughout the duct run.
Where This Tape Is Used
Use this tape to seal any ducting joint where an airtight connection is required — including joints between rigid pipe sections, around adapters and connectors, at wall outlets, and for repairs to existing ventilation ducting. Any air escaping at a joint directly reduces extraction performance at the hood, and sealing all joints is recommended for maximum efficiency regardless of the ducting system used.
Specification
- Width: 50mm
- Roll length: 45 metres
- Foil thickness: 40 microns — durable in demanding sealing and jointing applications
- Temperature rating: -40°C to +120°C — heat resistant for kitchen and commercial environments
- Adhesive: Self-adhesive, no primer required
- Fire resistant
✓ Aluminium foil ducting joint tape — 50mm wide, 45 metre roll
✓ 40 micron foil thickness — durable for demanding sealing and jointing applications
✓ Temperature rated -40°C to +120°C — heat resistant for kitchen, commercial and industrial environments
✓ Seals ducting joints and adapters — prevents air escaping and maintains full extraction power throughout the duct run
✓ Self-adhesive silver foil — supplied on white paper liner; no primer required
✓ Fire resistant
✓ Suitable for rigid and flexible ducting systems — compatible with all duct pipe formats and sizes
✓ Suitable for joining ducting pipes, heating and ventilation repairs
✓ Fast UK despatch — express overnight service available
View details150mm to 125mm Ducting Reducer Collar — 6" to 5"
This reducer collar steps down the ducting diameter from 150mm (6") to 125mm (5"), connecting a 150mm round spigot or duct outlet to a 125mm round ducting run. It is most commonly used to connect the motor housing spigot of a cooker hood or extractor fan directly to a 125mm round duct pipe where the motor outlet is 150mm but the duct run is 125mm. It is part of the Luxair 6" airtight ducting system.
Where This Component Is Used
Use this reducer wherever the ducting needs to step down from 150mm to 125mm — typically at the motor outlet where the hood's 150mm spigot connects to an existing or preferred 125mm duct run, or where a 6" duct section terminates into a 5" run. Always check your motor outlet diameter and intended duct size before ordering to confirm this is the correct reducer direction for your installation.
Ducting Size Guide
Selecting the correct ducting diameter for your motor output ensures maximum extraction performance:
- Below 450m³/hr → 100mm (4") ducting
- 450–750m³/hr → 125mm (5") or 150mm (6") ducting
- 750–2,000m³/hr → 150mm (6") or 200mm (8") ducting
✓ 150mm to 125mm ducting reducer collar — steps down from 6" to 5" round ducting diameter
✓ Connects 150mm motor housing spigot to 125mm round duct run — most common use at the cooker hood or extractor fan outlet
✓ Check motor outlet diameter before ordering — this reducer steps down from 150mm to 125mm; confirm direction before purchasing
✓ Push-fit airtight connection — no ducting tape, adhesive or clips required
✓ Part of the Luxair 6" (150mm) airtight ducting system — compatible with 220mm × 90mm flat and 150mm round components
✓ Suitable for kitchen, bathroom, utility room and whole-house extract systems
✓ Fast UK despatch — express overnight service available
View detailsThe Luxair 125mm to 100mm ducting reducer collar
The Luxair 125mm to 100mm ducting reducer collar connects a 125mm (5") round ducting outlet to a 100mm (4") round ducting run — the transition fitting used when your cooker hood has a 125mm outlet spigot but your existing ducting run, wall duct sleeve, or external wall vent is sized for 100mm. The collar is push fit on both ends, and ducting tape is recommended around both joints to ensure a fully airtight seal — particularly important on a reducer fitting where any air leakage at the size transition will reduce extraction performance and allow cooking odours to escape into the void behind your cabinets.
When You Need a Reducer — And When You Don't
A reducer is needed in one specific situation — when the outlet size on your hood doesn't match the size of your ducting run. The most common scenario is a new cooker hood with a 125mm outlet being connected to an existing 100mm duct sleeve in the wall — common in older UK properties where 100mm ducting was installed as standard and a newer, higher-rated hood is being fitted. Rather than replacing the entire ducting run, a single reducer collar solves the mismatch at the connection point. However, it's important to understand the trade-off — reducing from 125mm to 100mm will restrict airflow compared to running 125mm throughout. For hoods rated above 450 m³/hr, Luxair recommends running the correct 125mm, 150mm, or larger ducting throughout rather than reducing, to maintain full extraction efficiency.
The Right Way to Use This Reducer
Fit the reducer at the hood outlet only — connecting the 125mm spigot on the hood to the start of a 100mm run. Do not use a reducer mid-run to reduce pipe size after a straight section of larger ducting, as this concentrates the airflow restriction at a single point and significantly increases motor noise. The reducer is a practical solution for connecting to an existing 100mm wall sleeve — it is not a substitute for correctly sized ducting throughout a new installation.
125mm to 100mm — Check Your Hood's Outlet Size First
Before ordering, confirm the outlet diameter on your specific hood. The outlet spigot is usually found on the top of the hood body and is clearly marked in the installation manual. Common UK outlet sizes are 100mm, 120mm, 125mm, 150mm, and 200mm — and they are not interchangeable. If your hood has a 120mm outlet rather than 125mm, this reducer will not fit — check Luxair's full reducer range for the correct size.
All the other components for your ducting run are available as related products at the bottom of this page — add everything to your basket in one visit.
Ducting Size Guide by Motor Rating
Using this reducer means your effective ducting size is 100mm throughout. Confirm your hood's motor rating is suitable for 100mm ducting before using this fitting:
- Below 450 m³/hr → 100mm ducting is correct
- 450–750 m³/hr → 125mm or 150mm ducting recommended
- 750–2000 m³/hr → 150mm or 200mm ducting recommended
If your hood is rated above 450 m³/hr, consider whether upgrading the wall sleeve to 125mm or larger is a better long-term solution than reducing.
125mm to 100mm Round Ducting Reducer
Connects a 125mm (5") round ducting outlet to a 100mm (4") round ducting run. Solves size mismatches between hood outlet and existing ducting.
Push Fit on Both Ends — Ducting Tape Recommended
Push fit connection on both the 125mm and 100mm ends. Ducting tape is recommended around both joints to ensure a fully airtight seal at the size transition.
Tapered Internal Profile
Smooth tapered bore minimizes airflow turbulence through the size reduction.
Use at Hood Outlet Only
Fit at the connection between hood and duct run only — not mid-run. Mid-run reduction significantly increases motor noise.
Check Hood Outlet Size Before Ordering
Confirm your hood has a 125mm outlet spigot. Not compatible with 120mm, 100mm, 150mm, or 200mm outlets.
Suitable For Hoods Rated Below 450 m³/hr
Reducing to 100mm restricts airflow. For hoods rated above 450 m³/hr, correctly sized ducting throughout is recommended instead.
Fire Resistant Polymer Construction
Solid rigid fire-resistant polymer — safe for permanent installation.
Next-Day UK Delivery Available
In stock and available for express overnight delivery across the UK.
View detailsLuxair Thermobox® Heat Retention Cartridge — 125mm and 150mm
The Thermobox® is a multi-award-winning heat retention cartridge that fits within a 125mm (5") or 150mm (6") ducting vent or round ducting tube. It is a purely mechanical back-pressure shutter solution — no power required, no wiring, and it can be retrofitted to any existing ducting installation.
The Problem It Solves
Every ducted cooker hood extraction system has one weak point: the wall vent or duct outlet through the external wall. When the hood is not in use, this opening allows cold air to enter the building, warm air to escape, and on windy days produces the characteristic noisy flapping sound of standard vent flaps. In draughty or exposed properties this heat loss is continuous and significant — a permanent gap in the building's thermal envelope directly behind the kitchen.
How the Thermobox® Works
The Thermobox® ShutterTec retention system uses three flaps arranged in sequence, sealed by magnets. When closed, the three flaps create two sealed air chambers within the cartridge body. Air is a poor heat conductor — trapping it in sealed chambers creates an insulating barrier that performs up to 20 times better than a standard wall vent. When the extractor is running, air pressure from the motor opens the flaps automatically. When the hood is switched off, the magnets pull the flaps closed, sealing the chambers and restoring the insulating barrier. No power, no sensors, no maintenance.
Key Benefits
For properties in exposed or windy locations, the Thermobox® also eliminates the noise of flapping vent covers and prevents cold air being pushed back into the kitchen by wind pressure — a common problem with single-flap wall vents that standard back-draught shutters cannot fully address.
*Please note - the 125mm/5" version will only fit within the semi-rigid ducting or the flexible duct and will not fit within the rigid pipe.
✓ Luxair Thermobox® multi-award-winning heat retention cartridge — insulates up to 20× better than a standard wall vent
✓ Fits 125mm (5") and 150mm (6") round ducting and wall vents — check product title for size before ordering
✓ ShutterTec three-flap magnet-sealed system — creates two sealed air chambers when closed; opens automatically under motor airflow pressure
✓ Eliminates heat loss through the wall duct when the hood is not in use — seals automatically when extractor is off
✓ Stops cold air and draughts entering through the wall vent — effective in exposed and windy properties
✓ Eliminates noisy flapping vent covers — magnet-sealed flaps close silently and stay closed against wind pressure
✓ Purely mechanical — no power, wiring or maintenance required
✓ Retrofittable — fits within existing ducting vent or round ducting tube without modification
✓ Compatible with all 125mm and 150mm ducting systems — Luxair push-fit and all standard ducting formats
✓ Fast UK despatch — express overnight service available
View detailsAluminium Inline Ducting Silencer — 125mm and 150mm, Up to 22dB Noise Reduction
This inline ducting silencer significantly reduces the operational noise of a cooker hood extraction system by up to 22dB, depending on frequency. It fits directly into any 125mm (5") or 150mm (6") round ducting run and requires no modification to the existing installation — simply insert inline between two duct sections. Available in lengths from 460mm to 585mm — check the product title for the exact length before ordering.
How It Works
The silencer body is constructed from thick-walled aluminium tube for high stability and durability. Inside, a 25mm glass wool insert at 16kg per m³ density absorbs sound energy as extraction airflow passes through — attenuating noise across a broad frequency range by up to 22dB. The glass wool material is non-combustible, certified to DIN 4102, making it suitable for use in kitchen extraction systems where heat resistance is a requirement.
Where This Component Is Used
This silencer is fitted inline on any round ducting run — positioned between the cooker hood outlet and the wall vent to reduce the noise transmitted through the duct. It is particularly effective for ceiling cooker hood installations using round ducting, where the duct run passes through ceiling voids and the motor noise can resonate through the structure. For installations using flat rectangular ducting, use a round-to-flat converter collar to connect the flat duct sections either side of the silencer.
Ducting Size Guide
Selecting the correct ducting diameter for your motor output ensures maximum extraction performance:
- Below 450m³/hr → 100mm (4") ducting
- 450–750m³/hr → 125mm (5") or 150mm (6") ducting
- 750–2,000m³/hr → 150mm (6") or 200mm (8") ducting
✓ Inline ducting silencer — up to 22dB noise reduction — significantly reduces cooker hood extraction system noise depending on frequency
✓ Fits 125mm (5") and 150mm (6") round ducting — check product title for exact size before ordering
✓ 460–585mm length — check product title for exact length before ordering
✓ 25mm glass wool insert at 16kg/m³ density — absorbs sound energy across a broad frequency range
✓ Non-combustible glass wool — certified to DIN 4102 — suitable for kitchen extraction systems with heat resistance requirements
✓ Thick-walled aluminium construction — high stability and durability throughout the duct run
✓ Fits inline on any round ducting run — no modification required; insert between two duct sections
✓ Ideal for ceiling cooker hood installations — reduces motor noise resonating through ceiling voids and structural elements
✓ Compatible with flat ducting systems via round-to-flat converter collar — see Luxair ducting range for compatible adapters
✓ Fast UK despatch — express overnight service available
View details125mm Semi-Rigid Aluminium Flexible Hose — 3 Metres
This is a 3 metre length of 125mm semi-rigid aluminium flexible ducting hose. Unlike fully flexible corrugated tube, this semi-rigid hose can be bent into shape by hand and holds the position it is formed into — making it suitable for duct runs that require a firm, fixed-shape flexible section rather than a loose, unsupported hose.
Important — Not Part of the Push-Fit Airtight System
This hose is not part of the Luxair self-seal push-fit ducting range. To connect this hose to 125mm rigid ducting pipe, a 125mm collar connector is required (available separately in the Luxair ducting range). Ducting tape should also be used at all joints to ensure an airtight seal — unlike push-fit components, this hose does not self-seal at connections.
Specification
- Diameter: 125mm (inner bore)
- Length: 3 metres (compressible for transportation)
- Construction: Single-layer aluminium with 4mm corrugation depth
- Flexibility: Semi-rigid — hand-bendable and shape-retaining
When to Use Semi-Rigid vs Rigid Ducting
Semi-rigid flexible hose is the correct choice where rigid pipe sections cannot be installed due to restricted access, irregular angles, or tight spaces — but where a fully flexible corrugated tube would be too unsupported or loose for the installation. The semi-rigid construction holds the formed shape without additional support, making it particularly useful for short transition sections between rigid duct runs. For maximum extraction efficiency, keep the flexible section as short as possible — the 4mm corrugation depth creates more airflow resistance than smooth-walled rigid pipe.
Ducting Size Guide
Selecting the correct ducting diameter for your motor output ensures maximum extraction performance:
- Below 450m³/hr → 100mm (4") ducting
- 450–750m³/hr → 125mm (5") or 150mm (6") ducting
- 750–2,000m³/hr → 150mm (6") or 200mm (8") ducting
✓ 125mm semi-rigid aluminium flexible hose — 3 metre length
✓ Hand-bendable and shape-retaining — forms into position and holds without additional support; suitable for firm flexible sections
✓ Not part of the Luxair push-fit airtight system — requires 125mm collar connector and ducting tape at all joints for an airtight seal
✓ 125mm collar connector required — available separately in the Luxair ducting range
✓ Single-layer aluminium construction — 4mm corrugation depth; stated diameter refers to inner bore size
✓ Compressible for transportation — extends to full 3 metre length on installation
✓ Use where rigid ducting cannot be fitted — keep flexible section as short as possible to minimise airflow resistance
✓ Fast UK despatch — express overnight service available
View details125mm Aluminium Flexible Hose — 1.5 Metres, Fire Retardant
This 125mm aluminium flexible hose is designed to connect directly from the motor unit outlet of a cooker hood to the rigid ducting run above. The 1.5 metre length provides sufficient flexibility to bridge the gap between the motor spigot and the first rigid duct section, accommodating minor misalignments and vibration in the connection.
Fire Retardant — Why This Matters
Aluminium flexible hose is fire retardant and will not melt or shrink when exposed to the high temperatures produced during cooking and extraction. This makes it the only appropriate material for the section of ducting directly connected to the cooker hood motor.
⚠ Never Use Plastic Washer-Dryer Hose on a Cooker Hood
White PVC washer-dryer hose must never be used as cooker hood ducting under any circumstances. PVC hose is not fire retardant — it will melt, shrink, and collapse when exposed to cooking temperatures, creating a serious fire hazard. Despite being the same diameter as some cooker hood outlets, washer-dryer hose is completely unsuitable for extraction use. Always use aluminium flexible hose or rigid ducting throughout a cooker hood installation.
Ducting Size Guide
Selecting the correct ducting diameter for your motor output ensures maximum extraction performance:
- Below 450m³/hr → 100mm (4") ducting
- 450–750m³/hr → 125mm (5") or 150mm (6") ducting
- 750–2,000m³/hr → 150mm (6") or 200mm (8") ducting
The 5" Push-Fit System
This hose is compatible with the Luxair 125mm (5") push-fit airtight ducting range. The full system includes rigid round and flat pipe sections, bends, elbows, adapters, and wall outlets. Use ducting tape or a collar connector at joints where push-fit components are not used to ensure an airtight seal throughout the duct run.
Key Features tab:
✓ 125mm aluminium flexible hose — 1.5 metre length
✓ Fire retardant — will not melt or shrink at cooking temperatures; the only appropriate material for direct motor outlet connections
✓ ⚠ Never use plastic washer-dryer hose on a cooker hood — PVC hose is not fire retardant and is a serious fire hazard in extraction installations
✓ Connects directly from motor unit outlet to rigid ducting run — 1.5m length accommodates misalignment and motor vibration
✓ Compatible with the Luxair 5" (125mm) push-fit airtight ducting system
✓ Use ducting tape at non-push-fit joints — ensures airtight seal throughout the duct run
✓ Fast UK despatch — express overnight service available
View detailsUniversal 5-in-1 Louvred Wall Vent — 100mm, 125mm and 150mm
This universal louvred wall vent is a single grille that covers virtually every standard ducting size in one product. By snapping off the sections you don't need, it adapts to fit any of the following ducting formats:
- 100mm round ducting pipe
- 125mm round ducting pipe
- 150mm round ducting pipe
- 100mm × 60mm flat rectangular ducting
- 150mm × 70mm flat rectangular ducting
Select the section that matches your ducting size, snap off the rest, and fit. No additional adapters or collars required. Suitable for internal or external wall installation.
Where This Vent Is Used
Ideal wherever a single universal solution is needed to terminate a duct run at an internal or external wall surface — particularly useful for installations where the ducting size may not yet be confirmed, or for trade use where a single vent SKU needs to cover multiple ducting sizes across different jobs.
Ducting Size Guide
Selecting the correct ducting diameter for your motor output ensures maximum extraction performance:
- Below 450m³/hr → 100mm (4") ducting
- 450–750m³/hr → 125mm (5") or 150mm (6") ducting
- 750–2,000m³/hr → 150mm (6") or 200mm (8") ducting
✓ Universal 5-in-1 louvred wall vent — one product fits five standard ducting sizes
✓ Fits 100mm, 125mm and 150mm round ducting — and 100mm × 60mm and 150mm × 70mm flat rectangular ducting
✓ Snap-fit sections — remove the sections you don't need to match your exact ducting size; no tools required
✓ Internal or external wall installation — suitable for both interior outlets and exterior wall vents
✓ White plastic finish — suitable for most interior and exterior wall surfaces
✓ No additional adapters or collars required — complete solution in a single product
✓ Fast UK despatch — express overnight service available
View detailsLouvred External Wall Vent with Backdraft Shutter
Luxair louvred external wall vents combine a durable polystyrol construction with a built in backdraft shutter system — preventing cooking odours, cold draughts, and insects from entering the property through the wall duct when the extractor is not in use. Available in four colours and three size options to suit any exterior finish and any standard ducting diameter up to 150mm.
Red Dot Design Award Winners
These vents are Red Dot Design Award winners — recognised for combining aesthetic appeal with practical ventilation performance. The louvred face design provides effective airflow when the extractor is running while maintaining a clean, considered appearance on the external wall.
Colours and Sizes
- White (RAL 9010) — 100mm, 125mm, 150mm
- Brick Red Terracotta (RAL 8004) — 125mm, 150mm
- Light Grey (RAL 7042) — 125mm, 150mm
- Anthracite Grey (RAL 7016) — 125mm, 150mm
Select your colour and size from the options above. Check the product title to confirm the exact size and colour before purchasing.
Material and Durability
Constructed from robust synthetic thermoplastic polystyrol — polystyrol does not decay, rot, or degrade over time when exposed to humidity or atmospheric dampness. The backdraft shutter is built into the vent body and operates mechanically — opening under airflow pressure from the extractor and closing when the extractor is off, blocking reverse airflow without any power or maintenance requirement.
Pair With the Luxair Heat Retention Cartridge
For maximum energy efficiency — particularly in airtight or modern fabric first homes — pair these louvred vents with the Luxair heat retention valve. The combination eliminates backdrafts entirely and significantly reduces heat loss through the wall duct when the extractor is not running. Click here to view these.
Ducting Size Guide
Selecting the correct ducting diameter for your motor output ensures maximum extraction performance:
- Below 450m³/hr → 100mm (4") ducting
- 450–750m³/hr → 125mm (5") or 150mm (6") ducting
- 750–2,000m³/hr → 150mm (6") or 200mm (8") ducting
View detailsRectangular External Wall Vent — 220mm × 90mm and 150mm × 70mm Flat Ducting
This is the correct external wall vent for installations using 220mm × 90mm or 150mm × 70mm flat rectangular ducting. Designed and made exclusively for Luxair, it features a push-fit locking system and a built-in draught-proof non-return internal valve — preventing cold air, wind, and odours from entering through the duct when the extractor is not in use. Available in White, Terracotta, and Anthracite Grey.
Push-Fit Lock System
This vent uses the same patented push-fit system as the Luxair flat ducting range — connecting with an airtight seal and locking securely in place with no ducting tape, adhesive, or fixings required. It is designed to work as an integrated component of the Luxair flat ducting system rather than a generic add-on vent.
Non-Return Draught-Proof Valve
The internal non-return valve closes automatically when the extractor is switched off, sealing the duct outlet against reverse airflow, cold draughts, and wind pressure. The valve opens under extractor airflow pressure and requires no power or maintenance.
UV-Protected Plastic Construction
The vent body is manufactured from UV-protected plastic — resistant to fading, discolouration, and degradation from prolonged sun exposure on exterior wall surfaces. Available in three colours to complement a range of exterior wall finishes.
Ducting Size Guide
Selecting the correct ducting diameter for your motor output ensures maximum extraction performance:
- Below 450m³/hr → 100mm (4") ducting
- 450–750m³/hr → 125mm (5") or 150mm (6") ducting
- 750–2,000m³/hr → 150mm (6") or 200mm (8") ducting
✓ Rectangular external wall vent — fits 220mm × 90mm and 150mm × 70mm flat ducting — the correct outlet vent for Luxair flat rectangular ducting systems
✓ Designed and made exclusively for Luxair — integrated component of the Luxair flat ducting push-fit system
✓ Patented push-fit lock system — airtight seal, no ducting tape or fixings required
✓ Built-in draught-proof non-return valve — closes automatically when extractor is off; prevents cold air, wind and odours entering through the duct
✓ UV-protected plastic construction — resists fading and discolouration on exterior wall surfaces
✓ 3 colour options — White, Terracotta and Anthracite Grey
✓ Suitable for kitchen extractor fan and bathroom ventilation flat ducting installations
✓ Fast UK despatch — express overnight service available
View detailsThe Luxair premium round steel wall vent
Please note- the 4" AND 5" VENTS REQUIRE THE CONNECTOR COLLAR
...is a handmade steel ventilation grille for the external or internal termination of a round cooker hood ducting run — available in stainless steel, matt black, white, and anthracite to match your kitchen exterior, render finish, or surrounding fixtures. Built from hand-finished steel rather than moulded plastic, it's a permanent, weather-resistant fitting with an integrated fly screen, available with an optional 100mm or 125mm connector collar to complete the installation in a single order.
Round vs Square Which Wall Vent Do You Need?
Both the round and square Luxair steel vents perform identically and share the same features — the choice is purely about aesthetics and compatibility with your wall and ducting run. The round vent is the natural choice when your ducting run uses round pipe throughout, as the circular profile aligns directly with the round duct and requires no transition at the wall face. It also suits period properties, brick-built homes, and any exterior where a circular vent reads as more traditional or sympathetic to the building's architecture. The square vent suits contemporary rendered exteriors, new builds, and modern kitchens where clean geometric lines are preferred. Both are available in the same four colours choose based on your building and personal preference.
External or Internal One Grille, Both Uses
The round steel vent works equally well as an external wall vent terminating the ducting run on the outside face of an exterior wall, or as an internal wall grille where ducting passes through a partition wall and a finished face is needed on the internal side. The steel construction handles outdoor exposure without rusting, warping, or discolouring — unlike plastic louvre vents that become brittle and discoloured within a few years of UV and weather exposure.
Integrated Fly Screen Insect Protection Built In
Every Luxair round steel wall vent includes a built-in fly screen permanently integrated behind the grille face — preventing insects, wasps, and spiders from entering the ducting run when the extractor is off. The screen is fixed into the vent body rather than being a clip-on component, so it won't fall out, get lost, or be inadvertently removed during cleaning.
Four Finishes Matched to Your Exterior or Interior
Stainless steel is the most weather-resistant option and suits modern kitchens and contemporary exterior finishes — corrosion-proof and low maintenance indefinitely. Matt black coordinates with dark exterior joinery, black window frames, and bold kitchen schemes where a standard white vent would stand out. White is the most versatile choice for rendered exteriors, painted brickwork, white PVC surrounds, and white-walled interiors. Anthracite suits grey render, aluminium framing, and the darker exterior palettes increasingly popular in new build and renovation projects across the UK.
Optional Connector Collar Complete the Job in One Order
Add a 100mm or 125mm connector collar to connect the duct pipe inside the wall directly to the back of the vent grille — the fitting that completes the connection between your ducting run and the vent face. 6" options will fit straight onto 150mm rigid pipe or semi rigid ducting. Ducting tape is recommended around the collar joint to ensure a fully airtight seal at the wall termination point. If you already have the correct collar, select "Not Required". All other components for your ducting run are available as related products at the bottom of this page — add everything in one visit.
✓ Push-clip fitting system — no screws, no drilling required — clips directly into duct opening on interior or exterior wall surface
✓ Handmade 304 stainless steel or matt painted steel finish — rust-proof, corrosion-resistant, durable for internal and external use
✓ 3 sizes — 100mm, 125mm and 150mm — check product title for exact size before ordering
✓ 100mm and 125mm require a ducting collar — to fit onto 100mm and 125mm round tubes; collar available separately
✓ 150mm fits directly onto rigid or semi-rigid 150mm pipe — no collar required
✓ Integrated fly and insect mesh screen — prevents debris, insects and pests entering through the vent opening
✓ Internal or external installation — suitable for interior wall outlets and exterior wall vents
✓ Compatible with standard round ducting systems — 100mm, 125mm and 150mm
✓ Suitable for kitchen, bathroom, HVAC, dryer vent and utility room ventilation applications
✓ Fast UK despatch — express overnight service available
View detailsThe Luxair premium square steel wall vent
...is a handmade steel ventilation grille designed for the external or internal termination of a cooker hood ducting run — available in stainless steel, matt black, white, and anthracite to match your kitchen exterior, internal wall finish, or existing fixtures. Unlike mass-produced plastic louvre vents, this is a hand-finished steel grille built to last the lifetime of your kitchen installation, with an integrated fly screen and a weighted backdraught shutter that closes automatically when the extractor is off. Available with an optional 100mm or 125mm connector collar to complete the connection in a single order.
External or Internal — Two Uses, One Grille
This vent works equally well as an external wall vent — terminating the ducting run on the outside face of an exterior wall, allowing extracted cooking air to exit the building — or as an internal wall grille — used where ducting passes through a partition wall into another void or space and a clean, finished face is needed on the internal side. The square steel profile sits flush against brick, render, timber cladding, and internal plaster equally well, making it the right choice for both applications in a single product.
Integrated Fly Screen — Keeps Insects Out
Every Luxair square steel wall vent includes a built-in fly screen behind the grille face — essential for external installations where insects, wasps, and spiders would otherwise enter the ducting run when the extractor is off. The fine mesh screen is integrated into the vent body rather than clipped on separately, so it stays in place permanently without the risk of falling out or being accidentally removed during cleaning.
Four Finishes — Matched to Your Kitchen or Exterior
Stainless steel suits kitchens with stainless appliances and modern exteriors — and resists corrosion and weathering indefinitely on external walls. Matt black coordinates with dark kitchen schemes, black window frames, and contemporary exterior finishes where a standard white vent would stand out. White is the most popular choice for painted rendered exteriors, white PVC window surrounds, and internal walls with white plasterwork. Anthracite is the go-to for grey rendered exteriors, aluminium window frames, and kitchens with dark grey or slate colour schemes — the fastest-growing finish choice in new-build and renovation projects.
Optional Connector Collar — Complete the Job in One Order
Add a 100mm or 125mm connector collar to connect the duct pipe inside the wall directly to the back of the vent grille — the fitting that completes the connection between your ducting run and the vent face. 6" options will fit straight onto 150mm rigid pipe or semi rigid ducting. Ducting tape is recommended around the collar joint to ensure a fully airtight seal at the wall termination point. If you already have the correct collar, select "Not Required". All other components for your ducting run are available as related products at the bottom of this page — add everything in one visit.
✓ Push-clip fitting system — no screws, no drilling required — clips directly into duct opening on interior or exterior wall surface
✓ Handmade 304 stainless steel or matt painted steel finish — rust-proof, corrosion-resistant, durable for internal and external use
✓ 3 sizes — 100mm, 125mm and 150mm — check product title for exact size before ordering
✓ 100mm and 125mm require a ducting collar — to fit onto 100mm and 125mm round tubes; collar available separately
✓ 150mm fits directly onto rigid or semi-rigid 150mm pipe — no collar required
✓ Integrated fly and insect mesh screen — prevents debris, insects and pests entering through the vent opening
✓ Internal or external installation — suitable for interior wall outlets and exterior wall vents
✓ Compatible with standard round ducting systems — 100mm, 125mm and 150mm
✓ Suitable for kitchen, bathroom, HVAC, dryer vent and utility room ventilation applications
✓ Fast UK despatch — express overnight service available
View detailsHandmade Stainless Steel External Wall Vent
100mm, 125mm, 150mm and 200mm
These external wall vents are handmade from 304 grade stainless steel — rust-proof, corrosion-resistant, and built to withstand all-weather exterior conditions indefinitely. Available in four sizes to suit standard round ducting systems from 100mm to 200mm. Select your size from the options above and check the product title to confirm the correct size before ordering.
Construction and Finish
Fabricated by hand from 304 stainless steel with a brushed finish throughout. 304 grade is the standard for exterior architectural metalwork — it resists rust, salt air, and UV degradation without coating or treatment. Integrated louvres provide effective airflow when the extractor is running while directing moisture and debris away from the duct opening. Suitable for exterior wall mounting on any standard masonry, render, or cladding surface.
Applications
These vents are suitable for any exterior wall ventilation outlet including kitchen extractor fans, bathroom exhaust systems, utility room ventilation, HVAC and air circulation systems, and dryer vents.
Ducting Size Guide
Selecting the correct ducting diameter for your motor output ensures maximum extraction performance:
- Below 450m³/hr → 100mm (4") ducting
- 450–750m³/hr → 125mm (5") or 150mm (6") ducting
- 750–2,000m³/hr → 150mm (6") or 200mm (8") ducting
✓ Handmade 304 stainless steel external wall vent — rust-proof and corrosion-resistant for all-weather exterior conditions
✓ 4 sizes — 100mm, 125mm, 150mm and 200mm; check product title for exact size before ordering
✓ Brushed stainless steel finish — premium appearance suitable for modern and contemporary exterior finishes
✓ Integrated louvres — optimal airflow with moisture and debris protection at the duct outlet
✓ Compatible with all standard round ducting systems — 100mm, 125mm, 150mm and 200mm round duct connections
✓ Exterior wall mounting — suitable for masonry, render and cladding surfaces
✓ Suitable for kitchen, bathroom, utility, HVAC and dryer vent applications
✓ Fast UK despatch — express overnight service available
View detailsHandmade Stainless Steel External Wall Vent with Backdraft Shutter
These premium stainless steel external wall vents are handmade and feature a built-in backdraft shutter — mechanically closing when the extractor is off to prevent cold draughts, cooking odours, wind, and insects from entering through the wall duct. Available in 100mm, 125mm, and 150mm to suit standard kitchen extractor fan and bathroom ventilation ducting. Select your size from the options above and check the product title to confirm the correct size before ordering.
Backdraft Shutter — How It Works
The backdraft shutter is built directly into the vent body and operates entirely by air pressure. When the extractor runs, airflow pressure pushes the shutter open. When the extractor switches off, the shutter closes automatically — sealing the duct outlet against reverse airflow, wind pressure, and draughts. No power, no wiring, and no maintenance required.
Construction and Finish
Handmade from stainless steel with a brushed exterior finish — weatherproof, rust-resistant, and designed to complement modern exterior wall surfaces. The stainless steel construction ensures long-term durability in all-weather conditions without fading, discolouring, or degrading over time.
Pair With the Luxair Heat Retention Valve
For maximum energy efficiency in airtight or modern fabric-first homes, pair this vent with the Luxair heat retention valve for complete draught elimination and significantly reduced heat loss through the wall duct when the extractor is not in use.
Ducting Size Guide
Selecting the correct ducting diameter for your motor output ensures maximum extraction performance:
- Below 450m³/hr → 100mm (4") ducting
- 450–750m³/hr → 125mm (5") or 150mm (6") ducting
- 750–2,000m³/hr → 150mm (6") or 200mm (8") ducting
✓ Handmade stainless steel external wall vent with built-in backdraft shutter — prevents cold draughts, odours, wind and insects entering through the wall duct
✓ 3 sizes — 100mm, 125mm and 150mm; check product title for exact size before ordering
✓ Mechanical backdraft shutter — opens under extractor airflow pressure; closes automatically when extractor switches off; no power required
✓ Brushed stainless steel finish — weatherproof, rust-resistant, durable in all-weather exterior conditions
✓ Handmade construction — premium quality finish for modern and contemporary exterior walls
✓ Pair with the Luxair heat retention valve — for maximum draught elimination and energy efficiency in airtight homes
✓ Suitable for kitchen extractor fans, bathroom ventilation and utility room extract systems
✓ Compatible with all standard 100mm, 125mm and 150mm round ducting systems
✓ Fast UK despatch — express overnight service available
View detailsLuxair Automatic Airtight Wall Vent — 125mm (5") and 150mm (6")
The Luxair Automatic Airtight Wall Vent seals shut automatically when your extractor fan is switched off, preventing warm air from escaping through the wall duct and cold air from entering. It operates entirely by air pressure — when the extractor runs, the pressure opens the vent; when the extractor stops, low-maintenance springs return the vent to the sealed position. No electricity, no sensors, no maintenance beyond occasional cleaning.
How It Differs From a Standard Wall Vent
A standard wall vent uses a simple gravity or spring flap that provides minimal sealing — warm air escapes around the flap and wind pressure can force cold air back through the duct into the kitchen. The Luxair automatic airtight vent uses a full perimeter seal on the exterior cover, closing flush against the wall surface for maximum heat retention. Internal guide vanes reduce back-pressure within the duct run, improving extraction efficiency and reducing operating noise compared to a standard vent outlet.
Installation Guidance
For optimum performance this vent is recommended for use with cooker hoods rated above 650m³/hr — the motor needs sufficient airflow pressure to open the vent fully. Use with 125mm (5") or 150mm (6") ducting and keep the total duct run under 4 metres for optimal airflow and heat retention performance. Suitable for airtight and energy-efficient homes where standard wall vents create unacceptable heat loss.
Ducting Size Guide
Selecting the correct ducting diameter for your motor output ensures maximum extraction performance:
- Below 450m³/hr → 100mm (4") ducting
- 450–750m³/hr → 125mm (5") or 150mm (6") ducting
- 750–2,000m³/hr → 150mm (6") or 200mm (8") ducting
✓ Automatic airtight seal — vent closes flush against external wall when extractor is off; prevents heat loss and cold air entry
✓ Fits 125mm (5") and 150mm (6") round ducting — check product title for exact size before ordering
✓ No power required — fully mechanical operation using extractor airflow pressure to open; springs return vent to sealed position
✓ Stainless steel exterior cover — sleek round finish, flush-mounted against external wall with full perimeter seal
✓ Guide vanes reduce back-pressure — improves extraction efficiency and reduces operating noise versus standard wall vents
✓ Quiet and reliable — durable low-maintenance springs and joints; smooth silent operation in windy conditions
✓ Recommended for hoods above 650m³/hr — requires sufficient airflow pressure to open vent fully
✓ Recommended duct run under 4 metres — keeps airflow resistance low for optimal heat retention and extraction performance
✓ Suitable for airtight and energy-efficient homes — designed for modern builds and fabric-first retrofit projects
✓ Compatible with all Luxair 125mm and 150mm ducting systems
✓ Fast UK despatch — express overnight service available
- Automatic_Airtight_Wall_Vent_Instructions.pdf — Download
- 150mm_airtight_automatic_technical_sheet.pdf — Download
- 125mm_airtight_automatic_technical_sheet.pdf — Download
Manuals open in a new window.
No components match your search.
1 × Pyramid - 60cm to 110cm Wall Mounted Cooker Hood — Ivory-Cream / 60cm
These items are already added. The main product quantity reflects your basket; component selections add extra items.
View cart
